Edison Professional Bluetooth Speaker How To Connect

OPERATIONS Transmission FOR EDISON Professional
M-7500

OPERATIONS MANUAL FOR EDISON PROFESSIONAL

Introduction:

Congratulations on your purchase of an M-7500 powered loudspeaker, engineered and manufactured by Britelite Enterprises. The Thousand-7500 includes a high-output compression driver, and a xv″ woofer to produce an even, smooth studio-quality sound in a sound reinforcement speaker. Our blueprint goal was to build a speaker with accurate playback, smoothen dispersion of mid and high frequencies, and an ergonomic design for piece of cake transport and setup. The consequence is a sound reinforcement system dynamic enough to use at dwelling, in the studio, at parties, or in-home theater.

Features:

2-style amplified Active Speaker 2X15″ Long-throw woofer with high-temperature voice coil Ultra-wide, smooth dispersion of high and mid frequencies Mic/Line input and pass-thru connector USB & SD Menu input supports .wav & MP3 Bluetooth Compatible with TWS LED lighting

Cautions:

1. All Operating Instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do non open this unit. There are NO REPLACEABLE PARTS Within. Please refer servicing to a qualified service technician.
3. Do non expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. This unit should only be cleaned with a clammy cloth. Avoid solvents or other cleaning detergents.
5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce the gamble of damage during transit.
6. Exercise NOT EXPOSE THIS UNIT TO RAIN OR Wet.
7. DO NOT Utilize ANY SPRAY CLEANER OR LUBRICANT ON Whatever CONTROLS OR SWITCHES
8. Make sure All of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls earlier connecting a sound source.
9. Simply LINE LEVEL SIGNALS SHOULD BE SENT TO YOUR SPEAKER.

Disregarding whatever of the above will void your warranty!!!!

OPERATIONS MANUAL FOR EDISON PROFESSIONAL

1. MP3 module: Short press: Bluetooth, SD, USB, FM radio switch
   Short press: Repeat; Long printing: EQ setting
   Short press: Last and next; Long press: Volume – or +
   Brusque printing: Play or Suspension; Long printing: TWS
2. Master volume: Control the Volume of the speaker
3. Treble volume: Control the Volume of treble
4. Bass volume: Control the Volume of bass
5. Line input volume: Command the Book of line input
6. Microphone Volume: Control the Volume of the microphone input
7. Line input: XLR line input
8. Line output: an XLR line output
9. Microphone input: XLR microphone input microphone input
10. RCA line input
11. Microphone XLR input: 6.35 jack
12. Power Cord Connector
13. Power on/off
14. LED lighting on/off
15. 115-230 voltage switch

How to make two Thou-7500 wireless stereo-link

1. Long press "TWS" on the rear panel, 2 M-7500 will link automatically by Bluetooth
2. Enable Bluetooth on your smartphone, select "EDISON Professional"
   You tin enjoy your music now with two 1000-7500
   Delight note that the second speaker is sold separately.

How to use M-7500 remote control

1 →
Power: Media player ON/OFF.
Stop Media role player STOP. (Retention Carte du jour/ Flash Drive modes Just)
Mute: Media player MUTE.
two→
Mode: Media player Way selection.
Echo: Media histrion REPLAY way selection.(memory bill of fare/flash drive modes only)
EQ: Media role player EQ mode selection. (retentiveness menu/wink drive modes only)
3→
Reverse: Media actor Contrary control.
Frontwards: Media player FORWARD control.
Play/Interruption:Media histrion PLAY/Break control.
4→
Master volume down: Adjusts speaker chief volume DOWN.
Master volume up: Adjusts speaker master book UP.
0: Media role player track number and preset choice.
5→
ane-9: Media player rail number and preset pick.

How to switch the LED lighting of the speaker box
In that location is 5 mode of speaker box lighting, y'all can find the Cherry switch on the rear panel, you can switch the mode which you prefer.

1. Mode i: Multi-color automatically on when power on
2. Mode ii: Monocolour conversion
3. Mode three: Monocolour run
4. Mode three: Monocolour wink
5. Fashion iii: LED lighting off

Placement Tips

-Avoid placing loudspeakers in the corners of a room. This increases the low-frequency output and can cause the sound to be dingy and indistinct.
-Avoid placing loudspeakers confronting a wall. This, too, increases the low-frequency output, though not as much as corner placement. Yet, if yous practise demand to reinforce the low frequencies, this is a proficient way to do it.
-Avert placing the active speakers directly on a hollow stage flooring. A hollow stage can resonate at sure frequencies, causing peaks and dips in the frequency response of the room. Information technology'south better to place the speakers on a sturdy table or tripod stand.
-Position the speakers so the high-frequency drivers are ii to four feet above ear level to the audience to maintain high-frequency quality.

Troubleshooting

No Power
-Start check to make sure the speaker is plugged into a alive Air-conditioning outlet.
Make certain the POWER switch is on.

No Audio

-Make certain input LEVEL command is turned up.
-Brand sure the signal source is working and the connecting cables are in good shape and securely continued at both ends. Make certain the output volume control on the mixing console is turned up.
-Make sure the preamp or mixer does not accept a Mute push engaged.

Bad Sound – Noise – Bustling
If the sound is loud and distorted, verify that the levels are ready properly on the speaker and mixing panel.
Make sure all connectors are secure and they are plugged into the proper connector (i.due east., Mic cable plugged into MIC input, Line level source plugged into Line Level
Input. It is a good idea to periodically clean all electrical connections with a non-lubricating electrical contact cleaner.
Make sure none of the point cables are routed near AC cables, power transformers or other electrical power cords.
If humming occurs, turn the LEVEL command of the speaker all the manner down. If the noise disappears, it's coming from the signal source. If non, try disconnecting the cable connected to the INPUT jack. If the noise disappears, information technology could be a "footing loop," Try the post-obit ideas:
o, Use balanced connections throughout your system for best dissonance rejection. (XLR cables, balanced ¼" jacks; RCA cables are not balanced)
o Whenever possible, plug all the sound equipment's ability cords into the same outlet.
o The hum may appear when using an unbalanced source (CD player, iPod, etc.).
Use can apply an RCA to XLR adapter to turn an unbalanced cable into a balanced cable.
o If the hum persists, endeavor removing components i at a fourth dimension from the back of the mixer and check each for hum. Reducing the Bass or Treble levels (x and 11) may reduce humming.

Care and Maintenance

Your active speakers volition provide many years of reliable service if you lot follow these guidelines:
Avoid exposing the loudspeaker to moisture. If they are gear up up outdoors, exist sure they are undercover if yous expect rain Avoid exposure to extreme common cold. If you must operate loudspeakers in a cold surroundings, warm up the voice coils slowly past sending a low-level signal through them for about 15 minutes prior to high-ability operation.
Use a dry out cloth to clean the cabinets. Only practise this when the power is turned off. Avoid getting wet into any of the openings of the cabinet, particularly where the drivers are located.
This device complies with role xv of the FCC Rules. Performance is subject to the following two conditions: (1) This device may not cause harmful interference, and (ii) this device must take any interference received, including interference that may
cause undesired functioning.

FCC alert:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's dominance to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part fifteen of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and tin can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Notwithstanding, there is no guarantee that interference will non occur in a particular installation. If this equipment does cause harmful interference to radio or goggle box reception, which can exist determined by turning the equipment off and on, the user is encouraged to endeavor to correct the interference by i or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dissimilar from that to which the receiver is connected.
-Consult the dealer or an experienced radio/Tv technician for help.
This equipment complies with FCC radiation exposure limits ready along for an uncontrolled environs. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your trunk.

IC warning

This device complies with Industry Canada licence-exempt RSS standard(south). Operation is subject to the following two weather condition: (1) This device may non cause interference, and (2) This device must accept any interference, including interference that may cause undesired performance of the device.

This equipment complies with IC RSS-102 radiation exposure limits fix forth for an uncontrolled surround. This equipment should be installed and operated with a minimum altitude of 20cm between the radiator & your trunk.

Limited Warranty

This Limited Production Warranty is provided past Britelite Enterprises. Britelite warrants to A client that the product is free from defects in materials and workmanship under normal use during the Warranty Menses of 90 days for parts and 1-yr labor. If the product fails to suit to the warranty and then Britelite or its authorized service will either repair or replace any non-conforming product, provided that the Client gives notice of noncompliance within the Warranty Period to Britelite by emailing [email protected] or calling 310-363-7110 (Mexico customers can call 0155 4624 0251). Please retain the original dated receipt every bit evidence of proof of purchase.
Please exercise not return the product to the dealer or place of purchase.
Contact Britelite directly for warranty support.

Documents / Resources

Source: https://manuals.plus/edison/m-7500-15-inch-dual-pa-speaker-system-manual

Share this post